| Author |
 Topic  |
|
|
photoexpress
USA
49 Posts |
 Posted - 23 April 2010 : 11:55:30
|
| Hi i have a Noritsu V50sm and i keep getting a refilling error message #035 on My Fixture 1 Please Help! Thank you in Advance! |
|
|
Noritsu Help
United Kingdom
1399 Posts |
Posted - 23 April 2010 : 12:04:00
|
Check the float switch on the Fix 1 tank is moving up and down freely, and is clean of crystals.
If the float switch is OK (Check in input check refilling level) there will be a problem with the water re-filling pump. |
 |
|
|
photoexpress
USA
49 Posts |
Posted - 23 April 2010 : 12:12:50
|
| hi i checked the input check and the refilling level is off for Fixture1 So now not sure what that means and what to do |
|
|
|
Noritsu Help
United Kingdom
1399 Posts |
Posted - 23 April 2010 : 12:39:43
|
It means either the level is too low, or the float switch has got stuck.
Remove the chemical filter pot from the sub tank, look in the hole and you should be able to see a black rod with a white float, poke with a screwdriver and check the float moves up and down freely with the level of the liquid. |
|
|
|
photoexpress
USA
49 Posts |
Posted - 23 April 2010 : 13:20:13
|
| OK IT MOVES freely but for some reason when i went and check the water pumps the fixter1 water pump detatched and i had water all over the floor was able to re attach it but will it automatically re fill up with water once i turn the machine back on |
|
|
|
Noritsu Help
United Kingdom
1399 Posts |
Posted - 23 April 2010 : 20:18:17
|
| You can go into mode, replenish/refill Water, Refilling water |
|
|
|
photoexpress
USA
49 Posts |
Posted - 14 May 2010 : 14:13:57
|
| hi i checked the pump and for some reason its pumping water into the tank but it takes a while then i get a refilling error message for fixture1 Not sure how to correct this |
|
|
|
Noritsu Help
United Kingdom
1399 Posts |
Posted - 15 May 2010 : 13:07:47
|
Measure the output of the Fix1 water pump, by going into Mode, Replenish/Refil Water, Replenishment, Pump Amount Setting & Pump Amount Measurement.
Measure at least 3 times to get an average reading.
If the measured value is significantly different from the value set, the poppet valves on the pump may need to be replaced. Also check that the inline filters are not blocked.
If you top up the fix 1 tank manually does the fix 1 refill level go to 'on' in input check mode? |
|
|
|
photoexpress
USA
49 Posts |
Posted - 15 May 2010 : 15:35:00
|
| HI I JUST TOPPED off the fixer 1 with fixer and check the input check and its still off for refilling plus it was also trying to keep refilling the fixture right after i yopped it off and did the close down check Not sure!??? |
|
|
|
Noritsu Help
United Kingdom
1399 Posts |
Posted - 15 May 2010 : 16:08:49
|
Check the Fix1 float switch is moving fully upwards. If the float switch is moving freely, and still not showing 'on' in input check mode when the float is pushed fully upwards, the float switch will most likely be faulty.
The machine will keep trying to refill with water as it relies on the float switch to go to 'on' to tell it to stop refilling. |
|
|
|
photoexpress
USA
49 Posts |
Posted - 25 May 2010 : 16:35:46
|
| hi thank you for the information i was able to replace the float switch and now the error message went away Thanks again for your help |
|
|
|
photoexpress
USA
49 Posts |
Posted - 27 May 2010 : 13:13:18
|
| hi for some reason i replaced the float switch is worked once when i did a shut down but now the input check says off again and i keep getting refill error again please help |
|
|
|
Noritsu Help
United Kingdom
1399 Posts |
Posted - 27 May 2010 : 17:21:32
|
Check the connector plug of the float switch is not corroded etc.
If you move the float to the very top by hand does it go to on in input check mode?
Was the float switch you replaced a new one? |
|
|
|
photoexpress
USA
49 Posts |
Posted - 02 June 2010 : 10:06:14
|
| hi the float switch was used and i moved the float switch up and down but the input check still says its off |
|
|
|
Noritsu Help
United Kingdom
1399 Posts |
Posted - 02 June 2010 : 17:58:36
|
| Probably the used float switch is faulty then. |
|
|
| |
Topic |
|
Refilling Error 035 NoritsuV50
